Thorssoli's MkVI Costume Buildup

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 10, 2008

• #1

I can't post anywhere but the noob forum yet, so I figure that after a good month of lurking it's time for my first post.

Here's what I've got going so far.

Step one, a low-res model to test for sizing:

Step two, a couple of hi-res models because I printed one the wrong size:

Step three, coat the paper models with fiberglass resin:

Step four, coat the inside with several layers of urethane casting resin for strength:

Step five, bondo and sand and bondo and sand and bondo and sand:

Step six, test fit the visor:

Stay tuned...

 

Ral Partha

Sr Member

• Jan 10, 2008

• #2

thorssoli said:

Step six, test fit the visor:

Stay tuned...

Click to expand...

This looks so.... Shakespearean.

Very nice looking work so far. Keep us updated!

 

Last edited by a moderator: Feb 25, 2017

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 10, 2008

• #3

Ral Partha said:

This looks so.... Shakespearean.

Click to expand...

Yeah, my buddy with the camera said, "Now you need to do that 'Alas poor Yorick.' pose." I'm glad it translated well.

 

Last edited by a moderator: Feb 25, 2017

V

Vexona

Well-Known Member

• Jan 10, 2008

• #4

I was thinking that too!

This looks awesome! Top notch bondo work

(I also really like that jacket 'Senor Juan' ;D )

 

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 10, 2008

• #5

Vexona said:

I was thinking that too!

This looks awesome! Top notch bondo work

(I also really like that jacket 'Senor Juan' ;D )

Click to expand...

Thanks for the compliment. The jacket is actually one of my old pairs of coveralls. Each of them has a different name on them. This is the Juan pair. I also have an Ismael pair and a Romeo pair.

 

Last edited by a moderator: Feb 25, 2017

S

shadow8136

Well-Known Member

• Jan 10, 2008

• #6

is that resin and the other stuff safe to breath?? or do i need a like a plastic mask or somethin

 

T

thoren

Jr Member

• Jan 10, 2008

• #7

nice work im still working on my test helmet so i can gauge about how many trys its gonna take me to get it "just right" but it looks like u are right in the zone lol i hope when i bondo the rest of mine it looks like that lol

keep up the good work!

 

S

Spartan 343

Member

• Jan 10, 2008

• #8

shadow8136 said:

is that resin and the other stuff safe to breath?? or do i need a like a plastic mask or somethin

Click to expand...

NO,,its not safe to breathe. Make sure you use a respirator

 

Last edited by a moderator: Feb 25, 2017

J

jimmyfu

Jr Member

• Jan 11, 2008

• #9

by using urethane casting resin for the inside, did you not need to fiberglass? and if so, how much casting resin did you use on the inside...? i'm just trying to determine how much to buy if that's the case

 

A

AoBfrost

Well-Known Member

• Jan 11, 2008

• #10

Did you trim the rim of the neck yet? it looks like it wouldnt fit you, but since you have a photo of you wearing it, it must be ok.

Then again, good work!

 

B

bevbor

Well-Known Member

• Jan 11, 2008

• #11

thorssoli said:

Click to expand...

"Something rotten... Or just a fumes of the fiberglass?"
JK

 

Last edited by a moderator: Feb 25, 2017

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 11, 2008

• #12

Busy day yesterday. I did a lot more sanding and grinding and added the details to the bottom of the brim before putting a bit of primer on it.

Mostly I didn't need to primer anything just yet, I just wanted to see it closer to one color.

I primed the child-sized version too.

I've also made a low-res version of the torso armor to test for fit before I spend a lot more hours making the high-res version with all of the details.

 

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 11, 2008

• #13

shadow8136 said:

is that resin and the other stuff safe to breath?? or do i need a like a plastic mask or somethin

Click to expand...

The urethane resin is listed as a respiratory irritant. The fumes aren't dangerous (in fact, they're not even detectable), but when it cures the sanding dust will cause you problems. All of this stuff is some sort of bad for you. I also mixed milled glassfibers and some silicate into the resin to make it harder. This makes it even more likely to kill you dead if you breathe enough of it.

In short: NONE OF THIS STUFF IS SAFE TO BREATHE!

If you don't have a respirator, don't play with any of this until you've got one. Make sure it's the proper type for the application you're using too. There are different types that filter out either vapors (fumes) or particles (dust). The filter elements are only good for a limited amount of exposure too. You can read more here: http://www.osha.gov/SLTC/etools/respirator..._selection.html so study up and protect yourself or skip it and get a Darwin Award.

 

Last edited by a moderator: Feb 25, 2017

S

supertaco

Member

• Jan 11, 2008

• #14

thorssoli said:

I've also made a low-res version of the torso armor to test for fit before I spend a lot more hours making the high-res version with all of the details.

Click to expand...

yippee someone used my size tester

 

Last edited by a moderator: Feb 25, 2017

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 11, 2008

• #15

supertaco said:

yippee someone used my size tester

Click to expand...

Yessir! It was very helpful. Otherwise I'd have ended up printing out all six bajillion pages of the high-resolution model and ended up with a child-sized version like you can see in the bottom right corner of that pic.

In other news, I'm almost done with the detailing. Now I just need the hose inserts for the cheeks and I'll be ready to build the molds...

 

Last edited by a moderator: Feb 25, 2017

S

SPARTAN405

Member

• Jan 11, 2008

• #16

Great progress so far, its looking good!

 

Ronin

Member

• Jan 12, 2008

• #17

Great Job!!!!!!! Your bondo work is Smooooooth! How did make the details under your brim?

 

S

smilie120

Sr Member

• Jan 12, 2008

• #18

thorssoli said:

Click to expand...

Is that on a boat? And Great job on your armour btw .

 

Last edited by a moderator: Feb 25, 2017

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 16, 2008

• #19

So now that I'm in the minor detail portion of the project, progress seems to be very slow. Yesterday I added the hose inserts for the cheeks and scored some of the grooves on the top and sides of the helmet.

Now I've got to add the rest of the details around the back of the neck and straighten out some of my bondo work and it will be ready for molding.

smilie120 said:

Is that on a boat? And Great job on your armour btw .

Click to expand...

Yes. I live on my sailboat, so I'm doing all of the clean parts of the project there late at night. Anything that involves dust or fumes or paint or anything else that will leave a mess gets done in my workshop ashore.

 

Last edited by a moderator: Feb 25, 2017

T

thorssoli

Well-Known Member

Pacific Regiment

• Jan 16, 2008

• #20

Ronin said:

Great Job!!!!!!! Your bondo work is Smooooooth! How did make the details under your brim?

Click to expand...

I started with a piece of styrene plastic about 1/16th" thick and cut it to fit the shape of the bottom of the brim. Then I cut out the recess where all of the details would go and used the cutout to make all of the various raised portions. Then I glued them all in place using a simple two-part epoxy. The epoxy attached the plastic details and filled in between the seams. Once I had everything lined up the way I wanted it, it was just a question of taping everything down to make sure it didn't migrate while the epoxy cured like so:

 

Last edited by a moderator: Feb 25, 2017