pipninja
Well-Known Member
- Member DIN
- S770
2nd most probably, but Installation00 definitely has the most advanced helmet
Pipninja's Ultimate Gungnir Helmet!
- Thread starter pipninja
- Start date
MarrowofStar
Jr Member
Oohh I'll have to look into that. Yours is still impressive with the whole camera set up! When I start the electronics of my helmet I'll definitely be taking notes
Lojak
Member
pipninja
Well-Known Member
- Member DIN
- S770
Another update!!! Today was front hood electronics!!!
First, I started with the mics for the hearing, and then I isolated them and put the speaker in.
Next it was on to the front speaker for the voice amp
From there I could put in the rest of the wiring, starting with the left side, and then the right!
I went on to test the parts I could, being the screen and the fans by plugging in the 12v power. All the fans worked, the lights worked, the red light was sufficiently dim that it didn't light up my face, and the night vision on the camera even worked! All in all, the systems I could test worked perfectly!
Now I just have to get the back plate done, which should get off the printer tomorrow, and do the final control electronics, the padding, and sand, smooth, and paint the back plate! All before Friday!!!
First, I started with the mics for the hearing, and then I isolated them and put the speaker in.
Next it was on to the front speaker for the voice amp
From there I could put in the rest of the wiring, starting with the left side, and then the right!
I went on to test the parts I could, being the screen and the fans by plugging in the 12v power. All the fans worked, the lights worked, the red light was sufficiently dim that it didn't light up my face, and the night vision on the camera even worked! All in all, the systems I could test worked perfectly!
Now I just have to get the back plate done, which should get off the printer tomorrow, and do the final control electronics, the padding, and sand, smooth, and paint the back plate! All before Friday!!!
pipninja
Well-Known Member
- Member DIN
- S770
So I think I've made a padding decision. Originally I really wanted to make my own, but since I am u
Severely limited on time, I think I'm just going to buy a helmet padding kit! It would also probably be more comfortable in the long run
I am going to go with this one:
Yzpacc Tactical Helmet Pads, Universal Replacement Ex Helmet Internal Memory Foam Pad Universal Helmet Padding Inserts Protective Mat for ACH Mich Team Wendy Fma EXF Helmet Military Fast Amazon.com
Severely limited on time, I think I'm just going to buy a helmet padding kit! It would also probably be more comfortable in the long run
I am going to go with this one:
Yzpacc Tactical Helmet Pads, Universal Replacement Ex Helmet Internal Memory Foam Pad Universal Helmet Padding Inserts Protective Mat for ACH Mich Team Wendy Fma EXF Helmet Military Fast Amazon.com
Nob1e Actua1
New Member
So do you think you will be able to get the helmet done before the con this weekend?
pipninja
Well-Known Member
- Member DIN
- S770
Hopefully!
pipninja
Well-Known Member
- Member DIN
- S770
Okay, so Washington gaming expo is finally completed, and spoiler alert, I did get to finish the helmet in time! So let's rewind the clock to show the build!
I'm going to break this up in multiple posts so I can keep track of all the photos!
First off, the back of the helmet finished printing! This was the crux of waiting to get the last of everything done!
From that, I popped the supports off and did a test fit
From there was priming and sanding
Then on to painting, starting with the zinc coat, and then the masking fluid and top coats!
For the stencil, normally I would use my cricut, but it was down, so I actually manually made the stencil by using some thin masking to measure out and guestimate the side box stencil
From there, it was instillation of the top light
From there, it was a full fitting
I'm going to break this up in multiple posts so I can keep track of all the photos!
First off, the back of the helmet finished printing! This was the crux of waiting to get the last of everything done!
From that, I popped the supports off and did a test fit
From there was priming and sanding
Then on to painting, starting with the zinc coat, and then the masking fluid and top coats!
For the stencil, normally I would use my cricut, but it was down, so I actually manually made the stencil by using some thin masking to measure out and guestimate the side box stencil
From there, it was instillation of the top light
From there, it was a full fitting
pipninja
Well-Known Member
- Member DIN
- S770
Now that all that was done, it was on to the technical parts, the electrical!
So first off, here were the electrical control boards that I had to install together. Having a colored electrical diagram was beyond helpful here!
The first step was fitting the control boards in, and then tacking them down so I could put on the cover plate
I made sure that I labeled all the wires before putting the cover plate on!
From there was soldering the plug connections. Having really long and maneuverable helping hands was incredibly invaluable here!
Then the focus was on this little plate, behind which was supposed to be power distribution. I tested the battery fit here.
The reason I say supposed to, is because we ran into a little trouble here. Amazon sent me the wrong buck converters, so I only had this step up converter, and I needed a step down converter. With that, I ordered a new one, and pushed forward with what we had.
At this point, I actually finished the helmet all the way for day one of Washington gaming expo, but for the sake of keeping it organized, we are going to jump ahead first. The new buck converters came in Friday afternoon, and I was able to put them in, and get at least the hearing working. This is another time where the long nimble helping hands were great!
After getting these installed, I put the cover plate back on, and the electrical was completed for the helmet.
So first off, here were the electrical control boards that I had to install together. Having a colored electrical diagram was beyond helpful here!
The first step was fitting the control boards in, and then tacking them down so I could put on the cover plate
I made sure that I labeled all the wires before putting the cover plate on!
From there was soldering the plug connections. Having really long and maneuverable helping hands was incredibly invaluable here!
Then the focus was on this little plate, behind which was supposed to be power distribution. I tested the battery fit here.
The reason I say supposed to, is because we ran into a little trouble here. Amazon sent me the wrong buck converters, so I only had this step up converter, and I needed a step down converter. With that, I ordered a new one, and pushed forward with what we had.
At this point, I actually finished the helmet all the way for day one of Washington gaming expo, but for the sake of keeping it organized, we are going to jump ahead first. The new buck converters came in Friday afternoon, and I was able to put them in, and get at least the hearing working. This is another time where the long nimble helping hands were great!
After getting these installed, I put the cover plate back on, and the electrical was completed for the helmet.
pipninja
Well-Known Member
- Member DIN
- S770
With the electrical done, it was on to finishing the helmet! Starting with final assembly
Now on to the best part, weathering! Starting with a chrome dry brush!
Next it was on to the wash. I prefer a darker muddy brown than a black or grey wash. I'm going for slightly thicker than milk consistency, and then I cover the entire piece in it before I start cleaning it up. I then dab paper towels to pick up mose of that wash, but leave behind a fair bit of grime.
And here is the finished helmet!
The last thing I did was add the padding!
And a final camera test
Now on to the best part, weathering! Starting with a chrome dry brush!
Next it was on to the wash. I prefer a darker muddy brown than a black or grey wash. I'm going for slightly thicker than milk consistency, and then I cover the entire piece in it before I start cleaning it up. I then dab paper towels to pick up mose of that wash, but leave behind a fair bit of grime.
And here is the finished helmet!
The last thing I did was add the padding!
And a final camera test
N8TEBB
Well-Known Member
- Member DIN
- S410
SUCH A COOL HELMET!!
I must ask, did you have any trouble running the fans and hearing/speaking system off the same battery? Did the fans cause interference or anything? I think the fans in my helmet could be causing a problem with the hearing assist system I have.
I must ask, did you have any trouble running the fans and hearing/speaking system off the same battery? Did the fans cause interference or anything? I think the fans in my helmet could be causing a problem with the hearing assist system I have.
pipninja
Well-Known Member
- Member DIN
- S770
Nope, everything is in parallel, and the speech and hearing have their own step down boards. I e had no cross connection issues at all. It might be that that step down board regulates its output, Because all of my fans run off of a higher 12 volt then the 3V of the hearing board. As far as the voice amp goes, I'm still trouleshooting feedback right now so it's not technically working
N8TEBB
Well-Known Member
- Member DIN
- S410
Good to know!
As for microphone feedback, I had trouble with that all of last year. The microphone I was using was able to pick up sounds that were quite far away, including it's own output from the speaker. I replaced it with a mic that had a much shorter throw, which helped a LOT. It may not be your solution, but it's at least worth pondering. Feedback isn't always a speaker placement problem I guess
Lungorthin
New Member
Your weathering looks so good
And actually doing a blind helmet but using a screen is crazy ambitious, huge kudos
I'm curious if the screen is disorienting and how's the depth perception?
And actually doing a blind helmet but using a screen is crazy ambitious, huge kudos
I'm curious if the screen is disorienting and how's the depth perception?
pipninja
Well-Known Member
- Member DIN
- S770
It's not disorienting at all, and the visor helps for the really up close depth perception
