Sandbagger's Iron Man builds - Now in STEEL.
- Thread starter BuildsByBaz
- Start date
- Status
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Thanks so much to my new random internet friend named Ben for dropping off his TIG today! You are so very kind and generous to give so freely mate! Now I can really get going on the suit!
These kids in their wards are going to go beserk with happiness!
Baz.
Thanks so much to my new random internet friend named Ben for dropping off his TIG today! You are so very kind and generous to give so freely mate! Now I can really get going on the suit!
These kids in their wards are going to go beserk with happiness!
Baz.
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
I should get a day or two next week to start welding.
Looks awesome, Glade I'm back on to watch this amazing build.
I should get a day or two next week to start welding.
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Some updates from the last few weeks. Sorry it's been so long.
I had a little practice run at TIG welding.
Finally, I have found something I am not only bad at... but I totally suck at beyond human comprehension.
I have absolutely no idea what I am doing at all.
This is so hard, it's almost discouraging enough for me to scrap the whole project.
- - - Updated - - -
It really is frustrating when you hit a wall like this.
Trying to keep my spirits up and a positive attitude on this, I picked up the correct grade of aluminium today, (5005). Clean, no paint or residue and the proper one for welding and anodising.
Got the aluminium supplier to guillotine some 1mm strips off the parent sheet so I can use the same grade as a filler rod when welding.
These should keep me going for a while.
- - - Updated - - -
NOPE NOPE NOPE NOPE NOPE!!! GAAAAAHHHHH!!!
This time I used clean sheet, no contaminants and had a practice weld. I was happy with it.
The moment I went to a suspended gap weld, it went to ****.
So I ground it back, cleaned it and had another go. Worse.
Stuff this. I'm about to give the whole project away.
- - - Updated - - -
Well, it's decision time. Time to close the door on the aluminium build.
Ben, who lent me the welder came to my aid today to see if I am trainable in TIG welding. I'm not.
The hardest part was accepting the fact that I am not good at something I really want to be. It actually comes as a relief. Time to move on to the things that I am good at.
TIG welding a job like this is something to be attempted by someone with years of TIG experience. Even then, it's a daunting job.
I know it is unrealistic to expect to be instantly good at it. I realise it does take a lot of time to practice, but it's time I don't have.
I'm going back to steel and going to be MIG welding, which I can do. The suit will be heavier sure, but still manageable. I can fabricate in steel in a fraction of the time it takes to do the same in aluminium.
I'd like to take this opportunity to thank Ben_Wilson publicly for his tremendous generosity and helping heart in this, as well as Mad_Mic3 for his very inforamative PM's he sent me to help, which look like he put a lot of time and effort into composing for me.
Here's 3 pics to illustrate the arrival at what I think is a sound decision to move on.
- - - Updated - - -
Playing with cold-rolled mild steel now. Very soft and easy to work.
Finally got the metal-cutting blade for the band-saw, cut two pieces out beautifully and as I switched the saw off, it went BANG! $40 Brand new blade broken.
I'm seeing a pattern of every time a door opens, another one closes on this project. How many years have I been at this? :wired:
Getting very fast at this part. Cut and shaped it in 1/2 an hour. Ready to weld. Should be able to get this welded up on Saturday.
- - - Updated - - -
Had a little win last night. My aircraft-grade tin-snips cut the smaller pieces with ease. Bottom lip cut in less than two minutes.
SUCCESS!!!!! I welded the steel faceplate all up this afternoon! A bit of fiddling with the settings on the welder as I am not used to welding steel this thin, (1mm). Now to grind it back and sand it smooth. Let the real suit begin!!!!!!!
Some updates from the last few weeks. Sorry it's been so long.
I had a little practice run at TIG welding.
Finally, I have found something I am not only bad at... but I totally suck at beyond human comprehension.
I have absolutely no idea what I am doing at all.
This is so hard, it's almost discouraging enough for me to scrap the whole project.
- - - Updated - - -
It really is frustrating when you hit a wall like this.
Trying to keep my spirits up and a positive attitude on this, I picked up the correct grade of aluminium today, (5005). Clean, no paint or residue and the proper one for welding and anodising.
Got the aluminium supplier to guillotine some 1mm strips off the parent sheet so I can use the same grade as a filler rod when welding.
These should keep me going for a while.
- - - Updated - - -
NOPE NOPE NOPE NOPE NOPE!!! GAAAAAHHHHH!!!
This time I used clean sheet, no contaminants and had a practice weld. I was happy with it.
The moment I went to a suspended gap weld, it went to ****.
So I ground it back, cleaned it and had another go. Worse.
Stuff this. I'm about to give the whole project away.
- - - Updated - - -
Well, it's decision time. Time to close the door on the aluminium build.
Ben, who lent me the welder came to my aid today to see if I am trainable in TIG welding. I'm not.
The hardest part was accepting the fact that I am not good at something I really want to be. It actually comes as a relief. Time to move on to the things that I am good at.
TIG welding a job like this is something to be attempted by someone with years of TIG experience. Even then, it's a daunting job.
I know it is unrealistic to expect to be instantly good at it. I realise it does take a lot of time to practice, but it's time I don't have.
I'm going back to steel and going to be MIG welding, which I can do. The suit will be heavier sure, but still manageable. I can fabricate in steel in a fraction of the time it takes to do the same in aluminium.
I'd like to take this opportunity to thank Ben_Wilson publicly for his tremendous generosity and helping heart in this, as well as Mad_Mic3 for his very inforamative PM's he sent me to help, which look like he put a lot of time and effort into composing for me.
Here's 3 pics to illustrate the arrival at what I think is a sound decision to move on.
- - - Updated - - -
Playing with cold-rolled mild steel now. Very soft and easy to work.
Finally got the metal-cutting blade for the band-saw, cut two pieces out beautifully and as I switched the saw off, it went BANG! $40 Brand new blade broken.
I'm seeing a pattern of every time a door opens, another one closes on this project. How many years have I been at this? :wired:
Getting very fast at this part. Cut and shaped it in 1/2 an hour. Ready to weld. Should be able to get this welded up on Saturday.
- - - Updated - - -
Had a little win last night. My aircraft-grade tin-snips cut the smaller pieces with ease. Bottom lip cut in less than two minutes.
SUCCESS!!!!! I welded the steel faceplate all up this afternoon! A bit of fiddling with the settings on the welder as I am not used to welding steel this thin, (1mm). Now to grind it back and sand it smooth. Let the real suit begin!!!!!!!
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Thanks gents. :thumbsup
Grind back with a flap disc. Looking good.
Thanks gents. :thumbsup
Grind back with a flap disc. Looking good.
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Did some fill-welding in low points and cracks then re-ground smooth.
Welded in some thin strips in the eyes. I'll be doing this right around the faceplate.
Thin strip filed smooth and shaped the edge. That's starting to give it some depth now.
Started on the next bits. Small steps and taking time will get this done.
Did some fill-welding in low points and cracks then re-ground smooth.
Welded in some thin strips in the eyes. I'll be doing this right around the faceplate.
Thin strip filed smooth and shaped the edge. That's starting to give it some depth now.
Started on the next bits. Small steps and taking time will get this done.
WandererTJ
Well-Known Member
Re: Sandbagger's Iron Man build
You got this!!!
Keep up the good work!
You got this!!!
Keep up the good work!
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Thanks for the encouragement mate!
I had a day off work today, so I spent most of it in the workshop. All the parts for the helmet cut out and beaten into shape, ready to tack together and weld.
Thanks for the encouragement mate!
I had a day off work today, so I spent most of it in the workshop. All the parts for the helmet cut out and beaten into shape, ready to tack together and weld.
RobotChicken
Well-Known Member
Re: Sandbagger's Iron Man build
Are you kidding, he's probably going to use galvanized nails!
Are you kidding, he's probably going to use galvanized nails!
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Me either! It's like a vendetta now...
- - - Updated - - -
Thanks dudes. Yes I will line it.
A few bits and pieces cut, shaped and ready to weld.
Handplate.
Knuckles.
Fingers.
Me either! It's like a vendetta now...
- - - Updated - - -
Thanks dudes. Yes I will line it.
A few bits and pieces cut, shaped and ready to weld.
Handplate.
Knuckles.
Fingers.
BuildsByBaz
Sr Member
Re: Sandbagger's Iron Man build
Sizing and aligning the steel parts.
Sizing and aligning the steel parts.
nikolojedison
New Member
Re: Sandbagger's Iron Man build
Those fingers look really good. How are you planning to fill the joints on the hands?
Those fingers look really good. How are you planning to fill the joints on the hands?
BlazedStarbon
Well-Known Member
- Member DIN
- S009
Re: Sandbagger's Iron Man build
You must be making Tony Stark proud with this build. Amazing work. :cool
You must be making Tony Stark proud with this build. Amazing work. :cool
- Status
Similar threads
- Locked
