DRChefboyRD
Jr Member
Are you sticking with a factory fresh paintjob, or are you going to grime it up a bit?
Sweed builds a Spartan
- Thread starter SpartanSweed
- Start date
- Member DIN
- S402
Mostly factory fresh, as after 4 years I still dont know how to properly weather armor
bearbot
New Member
I've been eyeing these gloves on Amazon for a bit but was worried about the existing hand plate on the gloves making it look too clunky once a costume hand plate is added. Does the thickness of the original hand plate cause any issues?
bearbot
New Member
The flat black looks dope dude.
- Member DIN
- S402
They haven’t in my experience
- Member DIN
- S402
Printer has been giving me some rough prints lately, worse than usual so I’m sanding a lot more. But we do have our two shins, moving onto the thighs
Last edited:
- Member DIN
- S402
More progress over the weekend, one shin has been fully painted and is waiting to be padded. Currently the other is close to paint, just needs a pass or two more of 400 grit to smooth out the rough bits.
Unfortunately there was a casualty on Sunday, a shovel fell off the wall and landed in my workspace, crushing the freshly painted belt plate. I intended to reprint it eventually but this is a good excuse as any!
Unfortunately there was a casualty on Sunday, a shovel fell off the wall and landed in my workspace, crushing the freshly painted belt plate. I intended to reprint it eventually but this is a good excuse as any!
ItsWonderWhyt
New Member
I had to replace a motherboard. End result: I threw the whole printer in the trash lol! I’m glad it went well for you!
The finish on Montana gold is just always a step above other paints. The green looks great and added bonus, complements the power tools
- Member DIN
- S402
It’s been a sec, but much progress has been made. Planet has come and gone which leaves two weeks to finish this thing!
I’ve printed both boots using what Noble has done on previous suits, just workshopping how they actually fit together.
Both thighs have been printed and are currently in the sanding pits.
The second shin is painted and awaiting a clear coat to smooth out its finish, with both shins ready to be padded.
Lastly the belt is fully sanded and together at last!
I’ve printed both boots using what Noble has done on previous suits, just workshopping how they actually fit together.
Both thighs have been printed and are currently in the sanding pits.
The second shin is painted and awaiting a clear coat to smooth out its finish, with both shins ready to be padded.
Lastly the belt is fully sanded and together at last!
Last edited:
Garthok2962
Jr Member
thanks for this those gloves and the rest of your suit look amazing the colours so vibrant i cannot wait to see the finished result
- Member DIN
- S402
Less than 2 weeks to c2, and everything is printed. I repainted a chest SSGLordBert gave me a while back to save time, but I’d like to make one that’s scaled a little better to me. This will work for c2 tho!
Now that the chest is done, strapping the biceps can begin
Now that the chest is done, strapping the biceps can begin
OMalley
New Member
A couple things...
Did you have to do anything special between coats of paint due to the mixing of brands? Or did you just not have any issues? I always find that mixing brands gives me wrinkles in the paint.
Thanks for the tip on the gloves. Added to the cart for when I (someday) finish my ODST, and get to start a spartan haha.
Lastly, what brand are those shoes? They look like they're probably more comfortable than what I was planning on using....
Did you have to do anything special between coats of paint due to the mixing of brands? Or did you just not have any issues? I always find that mixing brands gives me wrinkles in the paint.
Thanks for the tip on the gloves. Added to the cart for when I (someday) finish my ODST, and get to start a spartan haha.
Lastly, what brand are those shoes? They look like they're probably more comfortable than what I was planning on using....
- Member DIN
- S402
I’ve had a little issue with the paint not curing fully or spraying two coats too soon one after the other. Just make sure to wait for the paint to be fully cured before attempting to mix brands.
The shoes are tallmenshoes, which add a 4 inch lift to my build. Honestly that’s as high as I would go as far as any lifts. The best thing about the shoes is that you can use the clearance section since it doesn’t matter what they look like, they’re gonna be covered by armor!
ItsWonderWhyt
New Member
- Member DIN
- S402
It’s always a good time, this year is gonna be big! It’s short notice but last minute appearances are a thing!
Knight the ODST
New Member
I must know, what inspired your color choice?
- Member DIN
- S402
My armor coating is from one of the esports teams, Quadrant. Specifically its their playoff coating, which has the nice green I wanted to do!
- Member DIN
- S402
As of today, everything has been painted, with around half the suit being padded and/or strapped! Once I get everything put together, it’ll be time for a test fit.
Also Happy 4/05 Day!
Also Happy 4/05 Day!
- Member DIN
- S402
Test fit of the upper body while I wait for more elastic to arrive, 5 days to C2
